| XTP R HDMI |
| NOTE |
The XTP THDMItransmitterand XTPR HDMI receiver can be used together, with twisted pair cables linking the transmitter and receiver, or with other Extron XTP products. |
|
| NOTE |
*Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. |
|
|
| Video |
| Gain |
Unity |
| Resolution range |
Up to 1920x1200*, 2K, or 1080p (HDTV)
* reduced blanking |
| Signal type |
Single-link HDMI (or DVI-D*) |
| Digital video |
RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component video (HDMI), actively buffered (supports all single-link DVI (if using an optional adapter) and HDMI standards from 640x480 @ 60 Hz to1920x1200 @ 60 Hz) |
| EDID and DDC |
Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered. |
| HDCP |
Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI standards |
| HPD |
Supports hot plug detection (HPD) of display as a pass-through signal. |
| Maximum data rate |
6.75 Gbps (2.25 Gbps per color) |
| Maximum pixel clock |
165 MHz |
| Formats |
RGB and YCbCr digital video |
| Standards |
DVI 1.0, HDMI; HDCP 1.1 |
|
| Interconnection between transmitter and receiver |
| Connectors |
1 female RJ-45 per unit |
| Termination standards |
TIA/EIA T568B |
| Signal transmission distance |
330' (100 m) using shielded twisted pair or XTP DTP 24 cable |
| Cable requirements |
Solid conductor, 24 AWG or better |
| Cable recommendations |
400 MHz bandwidth, STP (Shielded Twisted Pair) |
| NOTE |
Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. |
|
|
| Video output |
| Number/signal type |
1 single link HDMI (or DVI-D*) |
| Connectors |
1 female HDMI type A |
|
| Audio |
| Gain |
Unbalanced output: 0 dB; balanced output: +6 dB |
| Frequency response |
20 Hz to 20 kHz, ±0.05 dB |
| THD + Noise |
<0.1% @ 20 Hz - 20 kHz at nominal level |
| S/N |
>90 dB, at maximum balanced output (unweighted) |
| Crosstalk |
≤-80 dB @ 1 kHz, fully loaded |
| Stereo channel separation |
>80 dB @ 1 kHz |
| Sampling rates |
32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz |
| Bit depths |
16, 20, 24 bit |
|
| Audio output |
| Number/signal type |
1 analog stereo (2-channel), balanced/unbalanced
1 digital audio, embedded with HDMI output
1 digital audio via S/PDIF output connector |
| Connectors |
(1) 3.5 mm captive screw connector, 5 pole
1 female HDMI type A (shared with video output)
1 female RCA jack |
| Supported formats |
|
| HDMI |
LPCM up to 7.1/24-bit/192 kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS-ES Discrete 6.1, DTS-ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel |
| S/PDIF |
LPCM up to 7.1/24-bit/192 kHz, Dolby Digital EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS-ES Discrete 6.1,DTS-ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel |
| Analog |
Analog stereo audio |
| Impedance |
|
| Analog |
50 ohms unbalanced, 100 ohms balanced |
| Digital |
75 ohms (for S/PDIF output) |
| Maximum level (Hi-Z) |
>+12 dBV balanced; +6 dBV unbalanced |
| Gain error |
±0.5 dB channel to channel |
| Volume control range |
-100 dB to 0 dB (control 0 to 100 in 1 dB steps) |
| NOTE |
Attenuation = volume number minus 64. The default is 0 dB = volume number 64. |
|
| NOTE |
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Communications — receiver |
| USB control ports |
1 front panel female mini USB B |
| USB standards |
USB 2.0, low speed |
| Program control |
Extron control/configuration program for Windows ®
Extron Simple Instruction Set (SIS ™ ) |
|
| Communications — external device (pass-through, unidirectional or bidirectional) |
| Serial control port input/output |
1 set of proprietary signals on a female RJ-45 jack |
| Serial control port output/input |
RS-232 (+5) via (1) 3.5 mm, 5-pole captive screw connector (uses 3 poles) (connector is shared with IR control port) |
| Baud rates |
Up to 115200 baud |
| Protocol |
Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none |
| Serial control pin configuration |
1 = Tx, 2 = Rx, 3 = Gnd |
| Ethernet pass-through port |
1 female RJ-45 connector |
| Ethernet data rate |
10/100Base-T, half/full duplex with autodetect |
| IR control port |
(1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 40 kHz |
| IR control pin configuration |
3 = Gnd, 4 = IR Tx, 5 = IR Rx |
| Relay number/type |
2 normally open relays |
| Relay control connectors |
(1) 3.5 mm captive screw connectors, 4 pole |
| Relay control contact rating |
24 V, 1 A |
|
| General |
| Power supply |
External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts |
| Power consumption |
|
| Device |
8.9 watts, 12 VDC |
| Device and power supply |
10.8 watts, 12 VDC |
| NOTE |
Each XTP receiver can be powered either locally by an external power supply or remotely usingan optional power injector. |
|
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling |
Convection, vents on sides and top |
| Thermal dissipation |
|
| Device |
29.9 BTU/hr |
| Device and power supply |
36.6 BTU/hr |
| Mounting |
| Rack mount |
Yes, with optional 1U high rack shelf |
| Furniture mount |
Yes, with optional under-desk mounting kit |
| Enclosure type |
Metal |
| Enclosure dimensions |
1.0" H x 8.75" W x 6.0" D (half rack wide)
(2.5 cm H x 22.2 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product weight |
1.6 lbs (0.7 kg) |
| Shipping weight |
4 lbs (2 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance |
|
| Safety |
CE, c-UL, UL
UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply. |
| EMI/EMC |
CE**, C-tick, FCC Class A**, ICES, KCC, VCCI |
| Environmental |
Complies with the appropriate requirements of RoHS, WEEE. |
| NOTE |
**CE and FCC testing is conducted with STP (shielded twisted pair) cable. |
|
| Product warranty |
3 years parts and labor |
| Everlast power supply warranty |
7 years parts and labor |
| NOTE |
All nominal levels are at ±10%. |
|
| NOTE |
Specifications are subject to change without notice. |
|
| (8.1-082114-D9) |
